A shaped facing is a separate piece of fabric cut from a pattern to the same shape and on the same grain as the garment edge it will finish. Interfacing should be applied to the facing piece of fabric, prior to any stitching. Fusible interfacings may be applied to the facing side of an extended facing.
In this post
Does a facing need interfacing?
Interfacing should always be used when facings are called for in a pattern–even if the pattern does not require interfacing. The interfacing prevents stretching or sagging of the neckline or sleeves, acts as reinforcement for the area, and gives the garment a smooth but firm body.
Why are facing and interfacing important?
Like a lining, it gives the garment a clean look, hiding the raw edge between the wrong side of the fabric and the wrong side of the facing. It also gives a garment extra strength in some areas, and you can use it as an extra design element in your garment.
What’s the difference between interfacing and interlining?
In brief, interlining and interfacing are two types of fabrics dressmakers use for the inside of garments. The main difference between interlining and interfacing is that interlining is used between the outer fabric and the lining whereas interfacing is used on the wrong side of a garment.
What is the purpose of interfacing?
Almost every garment you make requires some type of interfacing for inner stability. Interfacing supports the fashion fabric and adds crispness, not bulk. It is used to reinforce areas that are subject to stress and helps a garment maintain its shape, wearing after wearing.
How wide should facing be?
How wide should a facing be? A facing can be very narrow, for example 2.5cm (1in), or up to 10cm (4in) wide or even wider. Most are around 4-5cm (1½- 2in) wide. Facings are usually cut the same width all the way around, but sometimes a back neck facing is cut deeper at the centre back.
Where do you put the interfacing in a jacket?
Just like the jacket hem pieces, the interfacing extends ½” beyond the fold line of the sleeve. Step 6O And finally, create the hem interfacing piece for the under sleeve, the same as you did for the upper sleeve, 2” up from the bottom edge of the hem, from seam to seam.
What is the facing operation?
Facing is the process of removing material from the end and/or shoulder of a workpiece, using a special tool to produce a smooth surface perpendicular to the rotational axis of the workpiece.
Can I use interfacing as interlining?
While lining is made with smooth fabrics like silk and cotton, interlining fabric uses rigid materials like canvas flannel and non-woven fabric. In fact, interlining can sometimes be made with interfacing.
Is interfacing removable?
It may be a heavy fabric with batting added, or a lighter weight one like flannel or fleece. Interlining can be constructed separately from the actual garment (it’s sometimes removable), or used as an underlining. Underlining is a fabric added to fashion fabric for more body and/or opacity.
Can you use interfacing as underlining?
Underlining can be fabric, fusible or sew-in interfacing. The underlining is cut exactly the same size as the pattern piece. If fabric is used as an underlining it is basted to the wrong side of the fashion fabric. If interfacing is used it will be fused directly to the fabric and extended into the seam allowance.
What can I use instead of interfacing?
Muslin and cotton are the best substitutes for interfacing due to the ease they give for interfacing. They can be best used when pre-washed to avoid shrinkage, then a 3. 5 stitch length or wider baste stitch to substitute fabric for interfacing on the primary fabric.
Does interfacing make fabric stiff?
Interfacing is a sewing notion that is used to stiffen fabric or help a part of a garment hold its shape.
What type of interfacing should I use?
The most important thing to consider when choosing interfacing is the weight of your fabric. Never use interfacing that is a heavier weight than your fabric. It should always be a slightly lighter weight, but stiffer than the fabric that you are using.
How do you use fabric interfacing?
When a ready-made sew-in or fusible interfacing is not available, add in a broad fabric like poly cotton or cotton as interfacing. Using or adding in the fabric is recycling the fabric for interfacing. Machine or thread basting will hold this fabric in its position until the collar or a buttonhole is finished.
What is difference between facing and turning?
The generation of surfaces oriented primarily perpendicular to the workpiece axis are called facing. In turning, the direction of the feeding motion is predominantly axial with respect to the machine spindle.
What tool is used for facing on a lathe?
A facing tool is used for facing operation on the lathe to cut flat surface perpendicular to the piece’s rotational axis, the tool is mounted into a tool holder that rests on the carriage of the lathe, during the process, the facing tool will feed perpendicularly across the rotational axis of the part.
What is the difference between facing and turning in lathe machine?
In the turning operation, the tool generally reduces the diameter of the cylindrical workpiece, which can be done by cutting into the part for some depth and move the tool parallel to the axis of the part. While facing operation reduces the length of the piece, the tool is moved perpendicular to the axis of the part.
What type of fabric is interlining?
Generally, interlinings are soft, thick, and flexible fabric made of cotton, nylon, polyester, wool and viscose or their blends, which may be coated with some resins. There are two types of interlinings in use in the garment production: fusible and non fusible.
What interlining means?
Definition of interlining
: a lining (as of a coat) sewn between the ordinary lining and the outside fabric.