Most jeans have a 1/2 inch rolled hem. But if you like a deeper hem, you can make it up to an inch on a pair of jeans. Men’s jeans usually don’t have anything wider than that, but if you’re feeling fancy, go for it. But for this example, we’re doing the traditional 1/2 inch.
In this post
How much can a tailor shorten jeans?
one to one and a half inches
Waist gapping can be an issue with denim pants, but an experienced tailor can alter a waistband to nip it in a bit. Just be sure not to take in the jeans more than one to one and a half inches at the waist, as doing more can change the pocket positioning and front shaping of the jeans.
How many inches can pants be hemmed?
The waist of a pair of trousers can be let in or taken out 2-3″. Look inside the seat for extra fabric at the waistband – this, minus half an inch or so, is as far as you can take the pants out. Trousers are easily shortened, but lengthening them requires fabric at the hems.
How much should I hem my jeans?
Hem Length for Straight Leg Jeans and Pants
Near the bottom of the ankle, before your foot starts is a good point for the hem. However, if you desire a longer pant and the fabric works you can go longer. Just don’t go too short, a straight pant can easily look like a too-long ankle pant or “highwaters” when too short.
How much does it cost to get jeans shortened?
Denim
| Denim | Approximate Cost | |
|---|---|---|
| Hem | $10 – $20 | |
| *slimming works best on | Original Hem | $15 – $25 |
| non-distressed denim | Slim Leg | $25 – $35 |
| Adjust Waist | $25 – $35 |
How do you keep raw hem jeans from fraying?
To get perfectly frayed hems:
Throw your jeans into the washing machine and dryer to get a fluffier frayed edge, and then trim off any too-long threads if needed. As an optional step to prevent further fraying, you can try applying an anti-fray product along the hems and letting them air dry. Hope this was helpful!
How do I stop my jeans from curling when I hem them?
Thread your sewing machine with thread that matches your original hem thread. Sew your hem into place using a seam allowance equal to the original seam allowance you measured. Remove your pins. The interfacing will keep your hem in place and protect it from curling.
How many sizes down can pants be altered?
two sizes
The rule of thumb is that you can go down two sizes at a maximum, but a suit jacket or blazer only one size too large is a safer option.
How much can pants be altered?
Typically, adjusting from a full break to half break, or half break to no break, the Inseam should be shortened by about 0.5”. Our trousers can be lengthened by up to 1” and shortened by up to 4”. Learn more about Pant Break here.
Where should jeans hit your ankle?
When wearing ankle pants, the hem of your pants should be positioned immediately above or right on your ankle bone. At this length, you want to go with a slimmer ankle that is not too wide, as this will shorten your entire length.
Should I cut the hem off my jeans?
Essentially, cutting off the hem of my jeans creates a raw edge with just the right amount of distressing to where they have a laid-back look but can still be dressed up.
How do you know if jeans are too long?
Find jeans that are long enough to have a bit of a break (a small crease in the denim around your shin), rather than creating a stick-straight or overly stacked look. Remember, you can always roll your jeans up to make them shorter, but you can’t easily add length.
What is the right length for straight leg jeans?
A standard pair of straight-leg jeans should be ankle-length or hit your legs right above your ankles. Straight-leg jeans that extend past your ankles tend to bunch up and look messy. 3.
How do you shorten pants and keep the original hem?
- Try on your to-be-hemmed pants. Tuck the hem under to your desired length.
- Take off jeans and turn inside out.
- Take out all your pins and turn jeans right side out.
- Using your heavy duty needle and matching thread, sew a straight stitch very close to the existing hem.
- Fold hem down.
Do raw hem jeans last?
Yes, it did and still does. You may have already gathered that by how often I’ve wear these jeans on the blog. They’ve just become better with time. The hem is a little more worn from washing and is a fun detail mixed with an otherwise polished outfit.
Is it worth it to get jeans tailored?
You can get jeans that fit you great off the rack. And with a little bit of tailoring, you can get them to fit you damn-near perfectly. Tailoring jeans, a hard-wearing garment meant for the masses, might sound excessive. But if you live in your jeans every day, even the smallest alterations can make a huge difference.
How long does it take to hem jeans?
As a professional seamstress, I have hemmed hundreds of pants. Jeans, suit pants, and everything in between has come through my shop. Some of these hems can be done in 15-30 minutes. Others take an hour or more.
Do you tip a tailor?
Tipping seamstresses is not standard protocol. That said, anytime a talented seamstress goes above and beyond, offering a gratuity is a thoughtful gesture.
Does Hairspray stop fabric from fraying?
When there’s no needle threader in sight, reach for a can of hair spray. Spray the end of the thread, then pinch it with your fingertips to compress stray strands and prevent fraying. The hair spray will also stiffen the thread, so that it’s easier to pass through the eye of a needle.
How do I stop my jeans from ripping between my legs?
How to Prevent Jeans from Wearing Out in the Inner Thighs
- Wash less often and don’t use the dryer.
- Use detergent specifically for denim.
- Protect your jeans from the inside.
- Prep your jeans to prevent wear.
- Buy multiples and let your jeans breathe.
- Take a cue from the guys.
- The fit is a factor.
Can I just cut the bottom of my jeans?
Use fabric (or super sharp) scissors to cut the hem off your jeans. Cut slowly and follow your chalk mark so that you have a nice straight edge. It doesn’t have to be perfect, but you don’t want it uneven (unless that’s the style you’re going for!)