If you absolutely must have a volume level for your hi hats, I would suggest -20 db. But this can vary depending on the artistic effect you’re going for as well as how high the average peak volume of your song is going to be.
https://youtube.com/watch?v=AtPTp2Wv-E0
In this post
What frequency should hi-hats be?
between 300-3000 Hz
Typical hi-hats are usually between 300-3000 Hz dominant frequencies, and can extend up to 10-17k Hz for crispness, “air” and sparkle. The “shhhhhhhhh” sound is usually found at the 2-3k Hz range.
How do I make my hi-hat quieter?
5 Ways to Muffle Hi-Hat Cymbals
- Dampen Your Hi-Hats With Household Items.
- Muffle Your Drum Sticks.
- Purchase Quiet Drum Sticks.
- Brush Up on Your Technique.
- Invest in Low Volume Hi-Hats.
Why does my hi-hat sound tinny?
If you push too hard on your hi-hat foot pedal, you will choke the cymbals, and this is a sure way to make even the best cymbals sound average.
Should hi-hats be mono or stereo?
The kick and the snare should be mono, the open-hats and the toms should be panned, and the closed hi-hats can be both panned and stereo.
How should you EQ hi-hats?
EQ (cut): The base frequencies of hi-hats are often somewhere in between 500Hz and 2kHz. Apply a HPF right before these frequencies to keep a clean mix. Hi-hats are important in defining the high frequencies of a song. Therefore, we add a LPF at the peak of their frequency range at around 20kHz.
Should you EQ hi-hats?
Since hi-hats occupy a small frequency range, they experience the effects of processing much faster than other drum hits. This makes it easy to go overboard with saturation, EQ, and compression. The best defense against this mixing mistake is to work with good quality recordings.
Are smaller hi hats quieter?
Generally, the thinner (lighter) the hats (or any cymbal), the darker and quieter they are.
Can you use a hi hat as a crash?
You can do whatever you want. I’ve heard of people using 2 16″ crashes as hihats, the only real problem with this is placement. Using one half of a hihat as a crash wouldn’t be too bad, as long as you like the sound.
How do I make my cymbals quieter?
Duct tape truly is the solution to most things. There isn’t much it can’t fix. Putting tape on cymbals is a timely tradition that dates back decades. Putting tape on a cymbal will lower how much it resonates, leading to a softer sound.
How tight should hi-hat Clutch be?
A little loose gives a good “wash” too, when you want it. Rub your palms together…the looser you have the hats, the more of THAT action between the cymbals you get. The tighter the hats, the more the edges will stay in line with each other, and the result is more “clang” sound.
How can I make my cymbals sound better?
However, there are a few things you can do that will make your current cymbals sound slightly better.
- Upgrade Your Hardware.
- Improve Your Technique.
- Keep Cymbals Clean.
- Making Your Cymbals Sound Brighter or Darker.
- Soundproofing Your Drum Room.
- Adding Things to the Cymbals.
- Getting Better Cymbals.
What are the best hi-hat cymbals?
7 Best Hi-Hats for 2022
- 1 Paiste Formula 602 Modern Essentials Hi Hat Cymbals 15″: Best Hi-Hats for Versatility.
- 2 Paiste Signature Dark Crisp Hi-Hat Cymbals 14″: Best Hi Hats for Recording.
- 3 Zildjian A Avedis Hi Hat Cymbals 14″: Best Vintage Hi Hats.
- 4 Zildjian K Sweet Hi Hat Pair 14″: Best Hi Hats for Value.
Should mono be clap?
Most of the time, the main snare and claps in a mix should be mono for the same reason as the kick. Mono hits provide the most impact. However, there are a few exceptions. If you plan on stacking snare samples, you may consider putting them in stereo to provide each hit with a bit more width.
Should you kick in mono?
Pure mono would show a thin vertical line. I would recommend having your kick in pure mono. But its not detrimental to have a small amount of width on your bass. Just don’t take those low frequencies too wide.
Should you pan your drums?
Panning is one of the most crucial things you can use to make your drum sound fill the entire room. The kick drum, and in some cases the snare drum too, will usually be in the centre of sound, so it will not require panning.
How loud should a snare mix be?
The snare is the foundation of the backbeat, and typically one of the loudest elements in the mix. Next, bring the kick fader up until it sounds almost as loud as the snare. It should be loud enough that the low frequencies are rich and powerful, but not so loud that it masks the bottom-end of the snare drum.
What hi-hats Does Lars Ulrich use?
As far as cymbals go Ulrich has always favoured Zildjian, and the signature kit was no exception. At this point he was using two 14” Custom ‘Dyno Beat’ Hi Hats, one on his right and one on his left side, 17″ and 18″ A medium crashes, 16″, 17″, and 18″ A rock crashes, and 20″ Z Custom China.
What is a standard size for hi hat cymbals?
13″–14″
The traditional sizing for hi-hats is 13″–14″, with 12s, 15s, and 16s becoming more common in recent years. Ride — The ride cymbal is the other major timekeeper behind the kit.