Make Your Own Dresser Scarf
- Hello Readers!
- Trim off the ruff edge of the ¼ yd pieces.
- Cut one piece into 2” strips for the inner edge.
- Cut one piece into 3” strips for the outer edge.
- Sew the narrow strips onto both sides of the center.
- All the seams in this project can be ironed in towards the center.
In this post
How wide should a dresser scarf be?
Measure the depth of your dresser and then subtract 1 inch from that measurement to determine the width of your dresser scarf fabric.
How much fabric do you need for a scarf?
Cut the fabric to the desired length and width.
You can use 1.5 yards (1.4 m) for a moderate length scarf, or use 2 yards (1.8 m) for a long scarf. The width of the fabric will depend on how full you want it to be.
How can I protect the top of my dresser?
A protective pad or mat will protect your dresser top from scratches and stains. A glass or acrylic sheet will serve a similar purpose without obscuring the top of your dresser.
How long should a scarf be?
Traditionally, a scarf goes tip to tip. To do this, try holding your arms out so that the scarf reaches from your left finger across to your right one. On average, this scarf will be about 60″ long. Most short scarves are 55″ long, medium scarves are roughly 70″ extended, and long scarves are about 82″ in length.
What are the dimensions of a scarf?
On average, scarves are usually 6 to 8 inches wide, and anywhere from 3 to 10 feet long. This is a wide range, and more exact measurements are based on the style of the scarf, and on the size of the person.
How do you waterproof a dresser top?
There are three surefire ways to waterproof your wood for years to come. Use linseed or Tung oil to create a beautiful and protective hand-rubbed finish. Seal the wood with coating of polyurethane, varnish, or lacquer. Finish and waterproof wood simultaneously with a stain-sealant combo.
How do you protect wooden furniture tops?
Use custom table pads. Using table top protectors for wood is one of the best ways to prevent your wooden table from any scratches. You can use some desk pads to cover your table top. It provides comprehensive protection while being attractive and effective.
How many rows should a scarf be?
To measure, place the knitting on a flat surface, place the measuring tape under the needle, and measure down to the cast-on edge. Work the 6 rows of the pattern stitch. These are the rows that form the ridges at each end of the scarf. Repeat rows 9 and 10 until the knitting measures 6 inches from the cast-on edge.
How much should you cast on for a scarf?
To determine how many stitches you will need to cast on, take your (gauge per inch) x (total width in inches) and the total will be the number of stitches needed for your scarf. This means you will need to cast on 36 stitches when working with a gauge of 4.5 per inch in order to get a scarf that is 8 inches wide.
How many chains do you need for a scarf?
If you’re using a medium-width yarn, each chain will be about 1/4 inch. If you want your scarf to be 5 inches wide, then that would be 20 chains. For a thinner yarn, it might be 1/8 inch wide per chain, so you’d want to double that to 40 chains. If it’s a really chunky yarn, you could probably do 10-12 chains.
What is an oversized scarf called?
A SHAWL. The term refers to a larger piece of fabric, usually rectangular, but sometimes triangular or square in shape that can be wrapped around the body.
What is the best width for a knitted scarf?
When it comes to the width of your knitted scarf, it’s a matter of preference. The average width of a knitted scarf can range from 4.5” (11 cm) wide to 8” (20 cm) wide. Any wider and you cross over into Lenny Kravitz land. For this easy scarf knitting pattern, I’ll stay within the 5-6 inch range.
How long should a scarf chain be?
For a common scarf (not a cowl or infinity style), the most accepted way to determine length would be to make it as long as the person is high. For a 6-foot person, a good starting point for the scarf’s length would also be 6 feet.
How do you keep a scarf from fraying?
- Widen Seams. Cut sheer fabrics with a wider seam allowance.
- Sew French Seams. Create a French seam with a wider seam allowance.
- Use Interfacing. Using iron-on fusible interfacing on the edges works very well to stop fraying.
- Pinking Shears.
- Zig-Zag Stitch.
- Handstitch.
- Use a Serger.
- Bias Tape Bound Edges.