Bias binding is a great way to finish raw edges on garments. It’s a good alternative to using a standard facing, particularly if you are short on fabric.
In this post
What is the difference between facing and bias binding?
A typical facing is cut the same way as the bodice, where as a bias facing is shaped to the neckline using it’s stretchy abilities. Bias binding is when bias tape is used to enclose the raw edge of a neckline, armhole, or hem. In this case, the bias tape fabric is seen. It can be made of contrasting or matching fabric.
Can you use bias binding on neckline?
Howeve, you can use a bias tape finish on just about any neckline. If the pattern you’re using doesn’t have a bias pattern piece, you’ll want to cut a strip of bias that is a few inches longer than your neckline seam. The width is up to you; the rule is it should be four times wider than the finished width of the tape.
Do you cut facing on the bias?
Why Does The Bias Tape Have To Be Cut On the Bias? You should cut tape for bias facing on the bias as it has more stretch than tape cut on the straight grain. That stretchiness will help you manoeuvre the tape around the curves of necklines and armholes more easily.
What is the purpose of facing in sewing?
Facing is mostly used to finish the edges in necklines, armholes, hems and openings. They are also used widely in all other sewing like quilts and home decor items like curtain hems. Shaped facings are cut to match the outside shape of the piece to provide a neat finish, and are often cut from the same pattern pieces.
How wide should a facing be?
How wide should a facing be? A facing can be very narrow, for example 2.5cm (1in), or up to 10cm (4in) wide or even wider. Most are around 4-5cm (1½- 2in) wide. Facings are usually cut the same width all the way around, but sometimes a back neck facing is cut deeper at the centre back.
How do you bind a Tshirt neckline?
Instructions
- Start With the Shoulders. Before you sew the neck binding, sew the shoulder seams.
- Sew the Neck Binding. Sew a short seam by folding the binding in half, right sides together, then stitching at the pattern’s seam allowance.
- Press.
- Pin the Neck.
- Keep Pinning.
- Get Out Your Machine.
- Backstitch.
- Finish Off the Seam.
How do you keep facing in place?
Flip the facing to the inside of the garment and press around the neckline. Because of the understitching, it will roll perfectly to the inside, taking a scant amount of the garment fabric with it, which keeps the facing on the inside at all times. Use your pressing ham to help press this curve.
Do you have to interface facings?
Both shaped and bias facings can be cut from a fabric lighter in weight than the garment to reduce bulk. If you have to alter the pattern, be sure to alter facings and interfacings to match. Interface a facing that will have buttonholes in it.
Why is bias binding cut on the cross grain?
Quilts with a curved edge need a little more flexibility from the binding in order to lay flat. Bias binding is cut at a 45 degree angle to the lengthwise grain and gives the fabric the most stretch possible, making it easier to manipulate around curves.
Why do you need to attach facing on the garments raw edges?
A facing is the area of a garment or sewn item that turns to the inside, giving a finished appearance to what would otherwise be a raw edge of the fabric. The facing is usually interfaced to add shape to the edge of the fabric and help the garment maintain the desired shape.
What is French bias binding?
French binding is a versatile bias binding technique that is used to enclose the raw edges of light weight and sheer fabrics. The finish is quite beautiful around necklines and armholes when neatly and meticulously done in either matching or contrast colours or fabrics.
How do you sew bias binding to a raw edge?
Stitch the binding ends together, trim the seam allowances and press them open. Pin the remaining binding to the raw edge. Stitch the binding to your garment, with the needle in the channel of the fold closest to the edge. Trim the seam allowances slightly, being careful NOT to trim the binding.
Can you use bias binding to hem?
As bias binding stretches with the curved edge, it’s perfect for finishing a hem on a circle or half circle skirt.
How many angles is the bias facing cut?
Bias binding is basically strips of fabric that are cut on the bias of the fabric. The bias of the fabric is a 45 degree angle from the selvedge edge.
How wide should armhole facing be?
The width of facing at the shoulder and at the underarm is usually between 1.5 and 2-inches.