In most cases, a skilled optician can make the proper adjustments to your frame and eyeglass temples so your glasses fit comfortably and stay in place.
In this post
How can I shorten my temple length?
Warming the temple tip for approximately 30 seconds in enough to pull it straight bend it and slide it down the temple. After you removed the plastic you can shorten the temple with a side cutter. After using the side cutter it is recommended to use a rasp and sandpaper to smoothen the edges of the end of the temple.
What happens if temple length is too long?
If the temple arm length is too long, the glasses will often fall forward because there is no support from the frames being hooked onto the backs of your ears. Once again, the length is identifiable by the digits on the inside of your frames, this time it is the last number of the three.
How do you lengthen eyeglass temples?
To raise or lower your frames:
- Heat both temples by soaking them in warm water for 30-60 seconds.
- To raise them, carefully bend them inwards until you feel a snug fit when you put them on.
- To lower them, carefully bend them outwards until they’re at the desired height.
How do I adjust my temples?
How to adjust tight or loose temples. If the temples seem straight but feel too tight or too loose, you can also adjust them by bending them upward or downward. For temples too tight at your ears, bend the end of the temples slightly upward. Most temples should bend at about a 45-degree angle just behind the ear.
What is the average temple length?
TEMPLE LENGTH
In other words, it’s the “arm length” of the frame. Temple length can fall between 120mm and 150mm with 135mm, 140mm, 145mm and 150mm being the most common.
How long should eyeglass temples be?
The temples of your frames should fit around your ears securely and comfortably. You should be able to shake your head without your glasses sliding down your nose. However, temple lengths also don’t vary all that much. They’re commonly offered in 5 mm increments: 135, 140, 145 and 150 mm.
How long should temple arms be on glasses?
Find your glasses arm length
If your temple width is 129mm or less, choose an arm length between 135mm and 140mm. If your temple width is between 130mm-139mm, choose an arm length between 140mm and 145mm. If your temple width is wider than 139mm, choose an arm length of 150mm or above.
How long should temple arms be?
2. Arm Length. Glasses’ arms (also known as “temples”) should extend straight back to your ears and only touch the side of your head just in front of your ears. The arms must also not curve too early; if they do, this will push the glasses down on your nose.
Should my glasses touch my cheeks when I smile?
Your glasses shouldn’t rest on your cheeks when you smile. They should be level on your face. The temples of your eyeglass frames should feel secure around or over your ears, without pinching or feeling uncomfortable.
How do Opticians adjust glasses?
The most common machine used to adjust acetate or plastic frames is the frame heater. Essentially if you’ve got a plastic frame that is one arm too high, or it’s been stretched from putting them on your head, rolled on them or sat off them, then we just need to heat the frame to bend it back into position.
How do you measure temple length?
THE TEMPLE ARMS
Measure from the hinge—where the arm connects in the front— to the spot where the arm begins to bend down around the ear. Then measure from the top of the bend to the bottom tip. Add the two sections together for the total temple arm length.
Can glasses be too close to eyes?
If the lenses sit too close, or too far from your eyes, this can change the power of the lenses themselves. Even with an accurate prescription, you may feel as though your glasses are “too strong”, or “too weak” because you have effectively produced a different powered lens.
What are temple tips?
Temple tips is the industry name for the arms of the glasses which go across the wearer’s temple. They’re not actually just tips, and they can have a big impact on how comfortable a pair of glasses is to wear.
What’s the difference between 52 and 54 glasses?
Lens width is measured from left to right at the widest point in the lens. Between a 52 and 54 eyesize, the 54 will have a wider lens so the whole frame will be wider too. The lens will also be a little taller to preserve the shape. The bridge and temple measurements will usually remain the same.
Should glasses be wider than your face?
The width of your frames should not be wider than the width of your face at the temples. The top of your frames should be no higher than the line of your eyebrows. The lower edge of the frames shouldn’t sit on your cheeks otherwise they will start to rub against your skin and cause irritation.
How do I know if my glasses are too big?
The curve should ideally begin just past the top of your ear. If your glasses are too big for you, the curve will not sit snuggly over the ear, keeping the glasses secure. This may be one of the reasons why your glasses keep sliding down the bridge of your nose.
Should glasses leave indent on side of head?
Your glasses also should not be so tight that they are leaving indents on the side of your head. If ignored, those indents can lead to prolonged pain such as headaches. If you are finding that you have markings then it is a tell-tale sign that your eyewear does not fit properly.
Should glasses touch your forehead?
The right pair of glasses should rest comfortably on the bridge of your nose, and should not press against your forehead or cheeks. But they shouldn’t rest so far towards the end of your nose that they slip when you squint or wrinkle your nose.
Should glasses cover your eyebrows?
But first, a few basic guidelines: The top of your glasses frame should follow the line of your eyebrows. Avoid having too much eyebrow above or below the frames. Sunglasses, however, should always cover your eyebrows.
Can you adjust glasses arm length?
You can bend them with your fingers or use a small pair of pliers to gently adjust the arms. Plastic frames need to be warmed before they can bend. You can warm the glasses in hot water for about 30 seconds or with a hairdryer, but be careful not to overheat.