Use a tape measure and measure 2” to 3.5” down from the collar on the front or back of the shirt. The idea is for the design to be printed on the intersection of the center line of the tee and the chest line. This will give you perfect placement on your custom shirts every time!
In this post
How far down to put a design on the back of a shirt?
Designs placed on the back of shirts should be approximately 5” from the collar and centered between the left and right seams. This option for logo placement is best for maximum exposure. Due to this part of the shirt, it has the largest real estate for your brand’s design.
How far down do you put vinyl on a shirt?
Measure 3″ – 3.5″ down from the center of the neckline. This is where the top of your design should fall. A good size for adult 2XL & larger shirts is 11″ x 11″ (up to 12″ – 13″.)
How far down from the collar should a design be placed?
Using a ruler, you’ll go 1.5 – 3 inches down from the collar, depending on the shirt size. For an adult size shirt, 3 inches down will be about that 3-4 fingers from the collar.
How far should a logo be on a shirt?
If a logo is to be embroidered on a T-shirt, it must be placed in the center of the chest, 4 to 6 inches down from the neck seam. Smaller logos are often put on the left side of the chest, 7 to 9 inches below the shoulder seam.
How far down do I place HTV on back of shirt?
Back designs should be placed using the center crease and four inches down from the center of the neckline.
How far down should a chest logo be?
Left Chest
The classic, and the go-to location for your logo when you’re providing shirts for employees, or staff for an event, or anything really. The size is tasteful; typically 3” to 4” wide, and around 3″ down from the collar. Placement can adjust to correspond with the size of the shirt, so it always looks right.
Where do they put vinyl on adult shirts?
Placing Heat Transfer Vinyl Tip: Fold in Half
When you unfold your shirt, you will be left with a line that you can use as your center point. You then fold your design in half (sticky side out) and crease the top to create an indention in the carrier sheet. Then you can line up the crease with the line on your shirt.
Do you need to prewash shirts before applying vinyl?
Additionally, a pre-wash is not always necessary either. If you prefer to wash your blanks, make sure to steer clear of liquid fabric softeners which leave behind a HTV repelling residue.
How big should a design be on an XL shirt?
ADULT
| Shirt Size | Standard Width | Suggested Design Width |
|---|---|---|
| X-Large | 24 inches | 11-12 inches |
| 2X-Large | 26 inches | 12.5-13.5 inches |
| 3X-Large | 28 inches | 13-14 inches |
| 4X-Large | 30 inches | 13.5-14.5 inches |
How Big Should design be on front of shirt?
Full front: The full front option has a standard size of 12”x16”, and it works best for more casual designs, usually for personal expression. Back collar: This is a much lesser used option and is quite small, measuring around 2” to 3” width times your preferred height.
Where do you position a logo?
upper left corner
Your logo should be in the upper left corner of websites, social media, and anything with text and images. Studies show top-left placement is the most effective for brand recall. Think about the way you interact with signs.
How big should an image be to print on a shirt?
The standard printing area men’s or unisex t-shirts is 12×16”, except for men’s XS, which is 10×12”. The standard printing area for women’s t-shirts is 10×12”, except for women’s XL and larger, which is 12×16”.
How big should a chest logo be on a shirt?
Although some left chest logos are smaller, it is recommended that these logos shouldn’t be bigger than 4 to 5 inches.
How do you align a logo on a shirt?
Most logos are left chest aligned allowing for a name, or a name patch to be placed on the right of the persons chest. The inside edge of the collar is used as a vertical center line for aligning the logo or design. The bottom of the logo is typically no lower than the bottom of the placket of the polo.
Why is the vinyl peeling off shirt after washing?
The iron on vinyl for shirts fall off when washing letters will happen more in the drye because the heat inside the machine can soften the fusible used in decorative applications. It is possible that these items were not properly cleaned before adding the design to the garment.
Why is my vinyl peeling off shirts?
Another reason your heat transfer vinyl is peeling involves your pressing temperature. When you inadvertently set your heat press to the wrong temperature, you either don’t melt the vinyl onto the fabric appropriately, or you damage the adhesive.
Why is my vinyl sticky after pressing?
This usually happens due to a lack of pressure at the time of pressing. We usually adjust the time and temperature correctly but increase the pressing time if the HTV doesn’t stick. Instead, we should increase the pressure.
How big should my shirt writing be?
The ideal size for the graphic on a long sleeve t-shirt is somewhere between 2.5” x 14” and 3.5” x 15.” You want to start the design about a finger down from the shoulder and make sure it doesn’t end up hitting the wrist area. Babies love custom printing, too!