Raglan Depth Measure in the center back from 1″ below the neck bone to the underarm level. Add 1/2″ to 2″ depending on how snug you would like the sleeve to fit against your underarm. This measurement would be used for a set in sleeve sweater or a seamed raglan style sweater.
In this post
How do you calculate raglan?
Multiply your wrist circumference + ease by your stitch gauge. Multiply your upper arm circumference + ease by your stitch gauge. Subtract the wrist count from the upper arm count and this will be the number of stitches that will need to be increased along the arm between the ribbing and the underarm.
How is raglan length measured?
3. Raglan The raglan measurement starts from the point where shoulder seam and neck opening meet, then runs diagonally down to where the sleeve meets the base of the armhole. In other words, when you make a top-down raglan, it’s the line along which you’ll increase.
How do you measure raglan sleeve armhole?
Preparation Sleeve
Draw the overarm seam from the shoulder point downward and shift it 2 cm to the front towards the hem. Measure the front and back from the armhole notches to the shoulder. Transfer the armhole measurements + 0.5-1 cm to the sleeve cap line. Draw the round overarm seam as illustrated.
How long should raglan sleeves be?
Three-quarter sleeve length: Length varies for this type of sleeve—raglan shirts can come in short sleeves or long sleeves—but the three-quarter length sleeve is a classic fit for raglan sleeve baseball tees.
How do you calculate stitches for raglan sweater?
There are 160 stitches on the body and 4 stitches cast-on at each underarm, so, the number of stitches on each back and front before the cast-on would be determined by subtracting each set of 4 cast-on stitches from 160, which gives us 152.
How do you measure shoulder width on a raglan sleeve?
Lay the raglan sleeve top flat. Place the end of the tape measure at the center backline as starting point. ※Measurement excluding rib trim.
What is armhole depth?
Armhole depth on knitwear is to the lowest part of the shoulder, so if measured from the center back you will be knitting an armhole depth that is actually the depth of the armhole, plus the rise of the shoulder, plus about another inch to the nape of the neck.
How is Armscye measured?
How is Armscye Measured? The Armscye measurement is taken from the tip of the shoulder, then around the edge of the bust, under the arm, and back up to the shoulder.
Are raglan sleeves good for broad shoulders?
Raglan sleeves help downplay the broad shoulders because they soften sharp edges.
Who should wear raglan sleeves?
Women may find a Raglan sleeved garment more flattering as there is no seam at the shoulders to sharpen the silhouette. People with large upper arms may benefit from a raglan as the fitting is wider in the underarm area than a Set-in.
What is a raglan increase?
Essentially in a raglan, you are working increases gradually and throughout the whole yoke. For a top-down yoke sweater, you are knitting increases only in about 4 rows of the total sweater, but doing a lot of rows without increases.
Can I knit raglan sleeves separately?
When working a raglan sweater pattern, each piece can be worked bottom-up or top-down. The body and sleeves can be worked separately in pieces that are seamed together or the body and sleeves can be worked in the round to the armholes, then joined and worked in a single piece to the neck.
Why is the front armhole of the sleeve pattern deeper than the back armhole?
Since the human shoulder is more rounded at the front of the body, the sleeve(cap) is more rounded there too, and the armhole is typically cut deeper into the front of the garment than the back.
What is back yoke depth?
Center Back Yoke Depth – at CBN, measure straight down from neck seam to yoke seam. Cuff/ Sleeve Hem Height – Measure from seam or stich line to cuff edge. Extended sleeve/cuff opening – Measure straight across, seam to seam, with all fullness pulled out.
Are raglan sleeves easier to sew?
I decided to feature raglan sleeves in this design as they can be sewn to the dress as flat pieces, before sewing the underarm, making them easier to construct than “set-in” sleeves, the kind that are sewn into a tube before being inserted into a round armhole (like on the Megan dress pattern from Love at First Stitch)
How do you measure shoulder width?
Instruct your friend to place the end of the measuring tape at the place where your shoulder meets the top of your arm, or, the boniest part of your shoulder. From there, holding the tape taut, they should stretch the tape straight across to the tip of your other shoulder blade. The measurement is your shoulder width.
What is the difference between armhole and armscye?
Armscye (also spelt arm scythe and pronounced ‘Arm’s Eye’) is a Scottish term in origin. It refers to the armhole opening in a garment and is also the tailoring term for the pattern shape used when constructing the armhole.
What is SYCE depth?
The scye depth (armhole depth), the position of the waist, and the length of the jacket are measured from the centre back neckline and are chalk marked according to the measurements. Lines are drawn 90° to the grain line at the scye depth, the waist, and at the jacket length mark.