The BOSS NS-2 Noise Suppressor is a studio-quality noise gate in the form of a compact pedal. It is the perfect answer to eliminating any unwanted noise in the signal chain. Noise gates work by automatically turning down or shutting off a signal when it drops to a certain level or threshold where it’s noticeable.
In this post
Is a noise suppressor pedal necessary?
Get a Boss pedal, noise supressor pedal, their great! And yes, you will need one eventually, when you play live, having a noise supressor pedal will eliminate all the uneccessary noises that no one likes.
What is the difference between a noise gate and a noise suppressor?
A Noise Gate defines thresholds that fully open allowing all of the sound to pass, or fully close to block the entire signal. A Noise Suppressor can also do this but has the added capability to let some of the signals sound pass by adjusting the sensitivity of the open / close thresholds.
Where should a noise suppressor go in the pedal chain?
Where does a noise gate go in your signal chain? In some ways, this is subjective. Naturally, you’ll want to place the noise gate wherever the noise is, for example after your fuzz pedal. It’s most common, however, to put it at the end of your chain but before any ambient pedals such as delay and reverb.
Is the boss noise suppressor a noise gate?
The Many Uses of the BOSS NS-2 Noise Suppressor
Still the industry standard of noise gate pedals, guitarists can use this flexible NS-2 in several ways to tame the buzz.
Do noise gate pedals affect tone?
All in all, noise gate pedals do affect tone. However, that change in tone may not be too strong to notice. Regarding the setting, there are a few things to consider. The threshold, which decides when the gate opens and closes, will affect the sound depending on how low or high you set it.
Does a noise gate go before or after distortion?
In general, though, the ideal position is right after the distortion pedal, because distortions (especially with high-gain settings) are one of the main noise-makers in your guitar rig: placing it after your overdrive, fuzz or any other distortion will cut out the bad unwanted frequencies.
Will a noise gate stop feedback?
There are also devices that can be purchased that could stop your feedback from occurring while jamming out. One of these devices is a noise gate, which is a device that controls audio signal volume and, in turn, could end up stopping feedback.
How does noise gate work?
A noise gate blocks any sound/noise coming through your audio channel once you set a noise threshold. When sound sits below this threshold the gate closes, blocking any noise. When sound is louder than this threshold, the gate opens and allows the sound through.
What is the best order for guitar pedals?
The best guitar effects pedal chain order starts with tuner pedals (closest to the guitar), followed by wah then fuzz. Dynamic-effects (e.g. compression) should go next, and then overdrive and distortion. EQ and modulation pedals should go next, and reverb and delay should go last in the chain.
What should my noise gate be?
Usually, a fast attack is your best bet when using a noise gate. You don’t want the beginning of a drum hit or vocal line to get cut off. So make sure your attack is fast enough that your recording isn’t getting clipped. Start with something under 5 ms and adjust from there.
Should fuzz go before or after overdrive?
Generally, your distortion, overdrive and fuzz effects pedals should go towards the start of your pedal chain as they have the greatest effect on the tone. Fuzz pedals should usually go first, followed by overdrive and finally distortion.
Do I need a noise gate on my pedalboard?
Noise gate pedals attenuate a signal that is below a certain threshold. That means that it cuts the signal and avoids unwanted hum. Therefore, when your gear produces undesired sounds, then noise gate pedals will be required.
What does a noise suppressor?
A noise suppressor (also called a noise gate) is a real problem solver, by being able to detect which part of the incoming signal is just noise and which is a guitar signal wanting to be amplified. A gate is a handy emergency device, when playing at different venues, each with its own set of electrical problems.
How do I reduce background noise on my mic?
15 Ways To Effectively Reduce Microphone Noise
- Choose A Condenser Or Active Mic With Low Self-Noise.
- Choose A Dynamic Mic With A Humbucking Coil.
- Place Mics Closer To The Sound Source.
- Use A Shock Mount.
- Use A Pop Filter.
- Record In Quiet Or Soundproof Environments.
- Use Balanced Mic Cables.
What is decay on a noise gate?
For the noise gate, I usually use a decay around 45%. Gives a more gradual “shutting off”. The threshold I’ll adjust it to a point so that when not playing, any noise from the amp/effects can’t be heard. Usually ends up around 35%, or a little lower.
How do I connect my boss ns 2 noise suppressor?
This is the simplest way to use the NS-2. Simply insert the NS-2 into your signal chain as the last item AFTER your noisy pedals or amp. The SIMPLE method, as the name implies, is simple to implement (you just connect it in-line, as you would any other effects pedal) and very effective at killing noise.
Where should a compressor go in the signal chain?
And the one that’s closest to our hearts: where do you place the compressor in your signal chain? The Official Textbook of Pedal Placement™ states that, apart from vintage fuzz and wah, compression should always be first in the chain.
When should I use an audio gate?
A noise gate is used when the level of the “signal” is above the level of the unwanted “noise”. The threshold is set above the level of the “noise”, and so when there is no main “signal”, the gate is closed.
How do you get high gain without feedback?
Turn down the gain on your amp or guitar.
- There should be at least two knobs on the face of your guitar. One of these should be the gain.
- You can keep the gain at three-fourths max or less on both your amp and guitar to prevent feedback. If you are still experiencing it, try turning it down even lower.
How do I stop my guitar from feeding back?
The easiest fix is to turn the amp down and get the guitar further away from it. The soundwaves that are feeding back through your guitar lose energy the further they have to travel. Moving your guitar away from the amplifier prevents these soundwaves from having enough energy when they get to your guitar to feedback.